EP brand replacement gearbox for woods rotary gearbox
NEW forty HP GEARBOX Easy Enter one 3/eight twelve spline output Interchangable with marketplace common dimensions i.e.: OMNI GRIZZLEY CHEETAH HOWSE KING KUTTER BUSH HOG HICO SILVER EDGE Many Much more
Characteristics
(1) manufacturer new forty five horse power shearpin gearbox. This gearbox matches numerous different helps make of 4′,5′ and some 6′ rotary cutters. I sell a good deal of these packing containers each calendar year for several diverse programs and carry ALL Alternative Parts for this box, but ideally you will not have to be concerned about that.
Listed here are the specs on the box:
*forty five horse power gearbox
*Normal 1-three/eight” sleek input shaft(exactly where the pto shaft hooks on). The pto shaft is held on by a 1/2 shearbolt.
*size of the enter shaft out of the gearbox is three” long
*bolt hole pattern for mounting is on the corners, 4-3/four centre of hole to heart of gap. It normally takes a 5/8″ bolt.
*12 splined output shaft(where the blade provider hooks up on the base)
*one-nine/16 outside measurement above the output shaft splines- from the base of the output cap to the finish of the splines is two-3/4″ lengthy- total duration of the output shaft is 4-one/two” lengthy.
*will take a 1″ threaded castle nut and a carter essential on the bottom of the output shaft to safe blade pan(NUT is included – – BLADE PAN IS NOT!!)
*general height of the box from the best of the mower deck to the leading of the box is nine-1/two”
This is a relatively large product (47 lbs.) so freight is not inexpensive, but we do not make anything at all off of freight, no matter what ups fees us we charge you.
40 HP
one:one:47 Ratio
one-three/8″ Sleek Input Shaft with Shear Pin Hole
1-1/2″ 12-Spline Ouput Shaft
Bolt Pattern: 6-one/2″ (4) five/8″ Holes, 5″ Middle Gap Required for Shaft Assembly
The Enter and Output Shafts Are not able to be Obtained Serparately.
They are Offered as a package.
The kit consists of the adhering to areas: input shaft, input gear, output shaft, output gear.
The Shaft Package Are not able to Be Separated.
EP model replacement gearbox for woods rotary gearbox
Rotary Cutter Gearbox Troubleshooting Guidebook
Is your mower leaking, creaking or otherwise carrying out improperly? You have arrive to the correct spot.
Go through below for the most frequent troubles with rotary cutter gearboxes and their solutions (from swift and dirty, to skilled).
Leaking Base Seal:
If you've got wrapped some baling or fencing wire all around your output shaft and blown the seal, the professional point to do is to replace the seal.
If your output seal is intact, and you are ready to get ID, OD and thickness measurements (in millimeters), most bearing houses can buy you up a generic double-lip seal that will get you again up-and-running. If not, give us a contact and we can help you form out what you want.
A dental select is the best way to take away the previous seal prior to pressing in the new one.
If you happen to be lucky adequate to have a gradual-leak, the rapid and soiled method is to operate automotive-type grease in the gearbox right up until the new seal will come in. Be positive to check out and insert grease a lot more usually than you would with oil, as this is NOT a professional mend.
Damaged Output Shaft:
Uh oh. You strike some thing that failed to move. The great information is that the output shaft on most gearboxes is pretty straightforward to change. The negative news is… it truly is hardly ever an isolated failure.
The very first issue to do is to just take apart your gearbox and evaluate the full extent of the harm. If it is really just the output shaft, you must be capable to adjust it out, no issue. The output shafts begin at about $70 and go up in cost dependent on the measurement of the gearbox.
However, in most instances, the bearings ($twenty/ea), seals ($10/ea) and equipment-set ($70) will also usually just take a beating. If you're unlucky, the output cap ($eighty) will also suffer some hurt.
In this scenario, it is normally less expensive to substitute the gearbox. Examine the price tag of parts to the cost of an total, new, warrantied gearbox. Occasionally, even specialists have to know when to get in touch with it a day.
I Want to Adjust my Enter Shaft:
If you are exhausted of shifting shear pins or hunting back and viewing that your mower has not been cutting, you may possibly want to set up a slip-clutch pto shaft (Yes, we market individuals too).
This typically requires setting up a 540-type, 6-spline enter shaft ($85) on your mower's gearbox.
Blessed for you, we did a create-up on our blog. It really is called “How to modify the input shaft on your rotary cutter gearbox”.
My Gearbox is Groaning/Creaking:
“Groaning”, “creaking”, or “popping” all sound sort-of related over-the-cellphone. The very best point to do is to disassemble your gearbox and just take a seem at the gears and bearings. The problem will generally present by itself in the way of damaged/lacking equipment teeth, toasted gears (like that photograph on our house web page), or blown bearings.
If every thing seems to be standard, try altering the equipment-mesh. This is accomplished with the mylar “gaskets” that sit in between the primary gearbox situation and the input/output caps. Try out introducing or taking away some of these spacers until finally your gears have roughly 1/eight”-1/4″ of free of charge perform. Professionals can purchase replacements ($one-two) in various thicknesses, but we advise the swift and soiled approach of reducing your possess out of a sheet of mylar.
Don't overlook to re-seal the gearbox with RTV after you have found the appropriate mixture. Even even though they're referred to as “gaskets”, they will not likely seal your gearbox on their very own.
Click on this link for more extensive as well as pleasurable content on Interpump Gearbox For PTO Drive.