helical bevel gear reducer

The EP Series Helical Bevel Reducer provides unmatched performance, durability, and design flexibility. This unit provides torque capacities up to 20,000 Nm (14,750 ft lbs).
The cat4CAD software allows simple interactive product collection of the entire gearbox and gear-electric motor system. Cat4CAD facilitates you in choosing and configuring the products, provides you the opportunity to print out intensive technical data bedding, and generates complete 2D drawings and 3D models for direct download.
11 sizes
Insight power capacities from 0.16 to 120 HP
Gear ratios from 5:1 to 8900:1
Torque capacities to 20,000 Nm
Inverter duty course F insulated motor windings
Course 12 Helical and Spiral Bevel Gears: Provides higher efficiencies and greater torques in smaller sized sizes.
Multiple Input Options: Integral gear motors, inch or metric shafts, NEMA, IEC, and servo adapters provide unmatched drive versatility.
Multiple Output Choices: Hollow bores and shrink disks for shaft installation, inch and metric output shafts, installation pilots and flanges provide an array of design solutions.
UNIBLOCK Housing: For maximum rigidity, universal installation on five sides or with a torque arm.
Worldwide Engine: Multiple leads and windings for globally multi volt/Hz requirements plus modular design to accept brakes, encoders or pressured cooling.
High efficiency motor design available
Innovative self-locking, self-aligning taper shaft engine connection
Gearbox supplied factory filled with synthetic oil
Corrosion and shock resistant cast iron housing
High efficiency helical-bevel gears. 98% per stage
Normally closed breather with multiple places (Optional OtN2000)
Double lip seals upon heat treated, plunge ground shafts
Shaft mounting choices include tapered bushings designs
This is a thorough offering of energy-efficient, right angle helical bevel enclosed gearing. It really is available as gearmotors and a variety of reducers with torque capacities up to 119,000 inch pounds. Housing designs include footed, face and flanged configurations. Gearmotors are available in three phase high efficiency designs through 50 HP and single phase to 5 HP. We provide a selection of input and result shaft options. Additionally, you will find fixed and variable acceleration motors and range of ratios obtainable in this product offering.
Features
Accommodates input power from ¼ Hp to 75Hp
Torque rankings up to 119,489 in-lbs
Reduction ratios up to 7,500:1
Helical – bevel – helical gear train offers cost effective high and low speed solutions
Up to 94% efficient
Four input possibilities for all units
Two output flange choices – B5 and B14
Multiple output shaft interfaces
Important dimensions interchangeable with major competitors
Modifications / Accessories
Integral Gearmotor
Clamp Collar C-Face Input
Solid Shaft Input
3-Piece Coupled C-Face Input
CEMA Screw Conveyor Adapter
EZ Kleen Washdown Package
XT Output Seals
Backstop
Heavy Duty Output Bearings
Inch or Metric Dimensions
Common Applications
Troughing Belt Conveyors
Slider Bed Conveyors
Mixer Drives
Screw Conveyors
Bucket Elevators
General Industrial Machinery
Common Industries
Aggregate and Cement
Air Handling
Chemical, Oil, and Gas
Food, Beverage, and Pharmaceutical
Paper and Forest
Unit and Baggage Handling
Water and Wastewater
As per the growing and varying demands of customers, we offer an array of Helical Bevel Equipment Reducers. The technological articles of our products permits an extraordinary performance/lifespan ratio. The extremely versatile Helical Bevel Gear Reducers we provide are successfully used in a vast number of industrial and civil applications. They are B-Series units which offer excellent affordability and output torque/weight ratio, especially considering that they need very limited servicing. Besides these, our products are available in cast iron (sizes 063 to 163) or aluminum (sizes A42 to A73) casing.
Features:
Sizes: 060-080-100-125-140-150-160
Available versions: B-fitted for motor coupling, IB with input shaft, CB with compact motor, PB-fitted for engine coupling with flexible joint
Casing with feet FC, flange SC and universal UC
Switch on to 90 kW
Gears hardened and tempered with shaved or surface profile
Gearing with 3 reduction stages
Gleason spiral bevel equipment pairs with run-in profile, mounted as second decrease stage for a higher resistance
Reduction ratios between 5, 71 and 187, 24
Torque max 13.000 Nm and admissible radial loads max 80.000 N
High-power casings optimized with FEM analysis and input and result flanges of grey cast-iron G200 to make sure top level performances and high reliability
Load capacity calculated and verified according to ISO 6336 and AGMA 2001
Painted with RAL 5010 blue epoxy-polyester powder
Accessories: torque arm, output flange, output shaft, shrink disk, backstop device, protection cover kit, viton oil seals, reinforced output, assemble/disassemble kit
Series EP right position helical bevel gear motors provide ratios from 8:1 to 160:1 in three levels or up to 10000:1 in five levels. Motors can be found up to 90kW and output torque capacity up to 12,300 Nm.
The series EP helical bevel gear motor is designed with integral cast feet for base or end mounting and will be offered with single or dual extended output shafts.
Systems are also available as shaft mounted or with output flanges and are designed for installation horizontally or vertically. The models can also be provided with a bolt on torque response bracket and all variants can be found possibly motorised or with an input shaft assembly.
Adding to the new range of Ever-Power helical gear motors the product takes advantage of our many years of accumulated design expertise together with the use of high quality materials and components. The end result is a series of acceleration reducing geared motors offering high load having capacities, increased efficiency, quiet running and reliability.
Top features of Helical Bevel Gear Motor
Standard motor connection
Capability to fit double oil seals, on input and output shaft since required.
All models are dimensionally interchangeable with additional major manufacturers.
Units are produced and assembled from a family group of modular kits for distributor friendliness minimizing inventory and maximizing availability.
Motorized units can be installed with a backstop module and reducer Models can be fitted with a backstop and fan.
Applications:
-Conveyors, Agitators, Elevators, Cranes, Crushers
-Helical Bevel gear motors are found in industries such as chemical substances, pharma, packaging, food processing, plastic-type material and automation etc.
Key Features:
Sizes: A40-A50-A70
Obtainable versions: EP – fitted for motor coupling, IEP – with input shaft, CEP – with compact motor
Cases with feet, flange or universal
Power up to 4,8 Kw
Gears with shaved or surface profile
Gearing with 2 and 3 reduction stages
Hypoid bevel gears for size A40 and A50, gleason bevel gear pairs for size A70, all with run-in profile
Reduction ratios between 7,62 and 442,76
Torque max 450 Nm and admissible radial loads max 5.500 N on hollow shaft and 10.000 N on solid shaft
Cases in die-cast aluminium alloy
Excellent mechanical strength while being and particularly lightweight
Load capacity calculated to ISO6336 and verified according to AGMA 2001-B88
Painted with RAL 5010 blue epoxy-polyester powder in according to DIN 1843
Accessories: torque arm, output flange, output shaft.
Generallntroduction of HK series:
Gear Reducer
The EP series gear units, are novel transmission gadget and made up of Y series motor, helical gear,Arc gear and worm
gear. The gears are made from high wear-resisting alloy materials, specifically and finely helical bevel gear reducer processed.
Advantages:
1: Helical-bevel equipment two-stage reducer
2: Compact framework, high efficiency
3: Quenched 20CrMnTi for gears
4: CE, ISO9001.
5: Compact design, small volume, wonderful appearance ,and strong capacity to be overloaded.
6: Precise division and wide range for transmission ratio.
7: The effectiveness is up to as high since 96% with low energy intake, strong adaptability and is with the capacity of functioning continually in corrosive or damp environment.
8: All- purpose use, convenient and low-cost maintenance.
9: New seal gadget, strong adaptability.
10: Varied selection of motor combinations, mouting positions and struture projects.